What is a CentaurPlus C11?

The Horstmann CentaurPlus C11 time switch will allow up to 3 ON/OFF settings per 24 hours and has a 1 hour manual boost and advance button to temporarily override current settings. There is also a programming switch allowing permanent selection of: OFF/ON/AuTO/All dAy. CentaurPlus C11.

How do I set the Horstmann heating timer?

How to set the clock on a Horstmann Electronic 7 water heater

1. Press the green “SET” button until the left-hand indicator points to “CLOCK”.
2. Adjust the hour with the “MINUS”/”PLUS” buttons.
3. Press the blue “SELECT” button to confirm the hour.
4. Adjust the minute with the “MINUS/PLUS” buttons.

How do you reset a CentaurPlus c17?

After initial installation it is advisable, before programming the CentaurPlus for the first time, to reset the unit. Resetting can only be achieved with the power ‘ON’ by pressing the SET and SELECT buttons together. This will return the programmer to the factory set default times.

How do you set a Horstmann CentaurPlus c27?

After initial installation it is advisable, before programming the CentaurPlus for the first time, to reset the unit. Resetting can only be achieved with the power ‘ON’ by pressing the SET and CH buttons together. This will return the programmer to the factory set default times.

How do you adjust a Horstmann t50 thermostat?

Press and hold SET and SELECT in Normal mode for 3 seconds to enter Clock setting mode. Clock, Day-of-Week, and “SET” are displayed. All other indicators are cleared.

How do I reset my Horstmann thermostat?

Besides, how do I reset my Horstmann thermostat? After installation of the batteries, push back the rear housing to the control centre and then the stand. Before turning on the main switch of the system, press the reset button once. The thermostat is ready for use.

How do I reset my Horstmann clock?

Lower the front flap of the unit. On the Hot water Channel press the ADVANCE and SELECT buttons together then release the buttons and the programmer will return to the preset factory settings.

How do I reset my Horstmann 7?

Resetting The Unit Sometimes electronic equipment can become scrambled or frozen. To overcome this you should reset the unit. This can be achieved by holding down “BOOST, MINUS, PLUS & SELECT” simultaneously.

How do you change the time on a Centaurplus c21?

1. 1 15.
2. Press BOOST. button once. for 1 hour of. hot water. Press advaNCe. button once to. move to the. next ON/OFF. time.
3. Press HW or. CH once. Programme. goes from. aUTO to. aLL day. Programme. will operate. from 1st ON.
4. Press the SeT. button until. SeT indicator is. next to PrOg. position. repeat this. process for. 2nd and 3rd. settings.

How does Horstmann economy 7 quartz?

The Horstmann Economy 7 Quartz is an Electro-mechanical water heating control, which can be set to take advantage of cheap night-rate electricity, so that there is a tank of hot water available for the morning.

How to use the Horstmann centaurplus C11 time switch?

OFF/ON/AuTO/All dAy. Page 1 CentaurPlus C11 User Operating Instructions Single Channel Timeswitch The Horstmann CentaurPlus C11 time switch will allow up to 3 ON/OFF settings per 24 hours and has a 1 hour manual boost and advance button to temporarily override current settings. There is also a programming switch allowing permanent selection of:…

How to set time in centaurplus C27 user operating?

Press the SET button until SET indicator is next to CLOCK position RUN CLOCK PROG Setting the Time of Day Use PLUS and MINUS buttons to adjust day Press ENTER 12:00 Use PLUS and MINUS buttons Press ENTER to adjust time Press the SET button until SET indicator is next to RUN position 6:35 RUN CLOCK PROG

What is the override function on centaurplus C11?

Manual Overrides BOOST FUNCTION – 1 hOUr TeMPOrary OverrIde The boost facility will allow the user to boost the system which is currently ‘OFF’ for 1 hour. To indicate the boost being activated BOOST will be shown on the display for the duration of the boost period.

Is there a way to reset the centaurplus?

After initial installation it is advisable, before programming the CentaurPlus for the first time, to reset the unit. Resetting can only be achieved with the power ‘ON’ by pressing the SET and CH buttons togetheL This w Il return the programmer to the factory set default times.