How do I reset my ProCurve 2610 24 to factory default?

To execute the factory default reset on the switch, perform these steps:

1. Using pointed objects, simultaneously press both the Reset and Clear buttons on the front of the switch.
2. Continue to press the Clear button while releasing the Reset button.
3. When the Self Test LED begins to blink, release the Clear button.

How do I reset my HP switch password?

If you lose or have forgotten a switch password: Solution: You can clear the switch password by pressing the recessed Clear button on the front of the switch. This action deletes all password and user name protection from all of the switch’s interfaces.

What is the default IP of HP switch?

192.168.2.10
In the factory default configuration, the default IP address of the HP ProCurve Switch Series 1800 and 1810 is 192.168. 2.10 and the subnet mask is 255.255. 255.0. These Series of Switches do not attempt to obtain an IP address via DHCP.

How do I reset my HP V1910 password?

HP V1910-48G JE009A Factory reset – Password recovery capability enabled.

1. Connect switch cable to COM.
2. Open Putty on COM 38400 – 8 – 1 – N.
3. Powercycle the switch.
4. Press Ctrl-B at boot to enter extended boot menu.
5. Skip current system configuration.
6. Reboot.

How do I reset my HP ProCurve 2510 to factory settings?

How to reset a ProCurve 2510-24g to default settings

1. Press in both the Clear and Reset buttons (tiny buttons on the left edge)
2. Release the Reset button after the port lights come on (~2 seconds)
3. When the Self-Test LED starts flashing (to the left of the Clear and Reset buttons), release the Clear button.

How do I reset my HP 8g 1920?

Restoring to factory defaults

1. Using a small, thin tool with blunt ends (such as a paper clip), press the Reset button on the front of the switch.
2. Continue to press the Reset button until the Fault LED light begins to flash.
3. Release the Reset button.

How do I turn off password recovery capability?

Password recovery capability is enabled. To perform this operation, first disable the password recovery capability using the undo password-recovery enable command in CLI. If password recovery capability is disabled, enter Y at the prompt to complete the task.

How do I restore my HP V1910 to factory settings?

To reset the config remove power from the switch, take a single Ethernet cable and plug it in to ports one and two on the switch, power it on, and wait! Give it a few minutes. That will reset all the ports on your switch to access ports on VLAN 1 – that’s it!

How to add password to hp 2610 switch?

A 2610 would have shipped with no password enabled and it would go straight into Manager (Enabled) mode via the console port. You add a named account in via “password manager user-name [name]” in a config context from looking at a 2610-24 I have. I would telnet/SSH into the switch and see if you can grab the config and then reboot it.

Is there a password on the HP ProCurve switch 2600?

The ProCurve Switch 2600 Series has no password protection by default. If only a password was configured via the CLI, try leaving the Username field blank, and entering only the password within the Web UI.

Is the HP ProCurve switch 2610 a fanless switch?

The HP ProCurve Switch 2610-24 is fanless, providing quiet operation and making it ideal for deployment in open spaces. The HP ProCurve 2610- 24/12PWR, 2610-24-PWR, and 2610-48-PWR are IEEE 802.3af-compliant for Power over Ethernet (PoE) and provide up to 15.4 W for 12, 24, and 48 ports. The 2610-24/12PWR has 24 10/100 ports and

How to change password on HP DeskJet 2600 printer?

Printer’s control panel: Select Administration settings or HP DeskJet 2600 printer Then choose Network settings, network setup or networking. Select Wireless Direct or Wi-Fi Direct , then choose Wireless Direct password or Wi-Fi Direct Password. The screen will get displayed where you can set or change the desired password.